RGB 9 Inch TFT with RTP Product Introduction
SFTO900SH-7170A4T is an 800 × 4800 high brightness TN TFT LCD display. The module size is 211.1(W)×126.5(H)×7.3(D) mm, with an effective area of 201.8 × 114.5 mm and a diagonal dimension of 9 inches. This TFT module adopts TN technology, with a typical aspect ratio of 4:3 and a wide viewing angle (70/70/50/70 degrees), which has a good cost advantage and enhances customers' visual experience of its products.
In addition, SFTO900SH-7170A4T offers three product features: high brightness (1000 cd/m2), high contrast (800:1), and anti glare. These features improve image display in complex lighting environments, enhancing the visual experience of customer products under various conditions.
The TFT module adopts 24 bit RGB interface (connector Hirose FT12A-50S-0.5H). The 9 inch series is an optional configuration for LVDS, MIPI, and RGB interfaces, depending on the requirements of the customer's MCU.
Features
| Item | Specification |
| LCD size | 9.0 inch(Diagonal) |
| Driver element | a-Si TFT active matrix |
| Resolution | 800 × 3(RGB) × 480 |
| Display mode | Normally White, Transmissive |
| Dot pitch | 0.0825(W) × 0.2327(H) mm |
| Active area | 198.000(W) × 111.696(H) mm |
| Module size | 211.1(W)×126.5(H)×5.9(D) mm |
| Module size(with RTP) | 211.1(W)×126.5(H)×7.3(D) mm |
| Surface treatment | Anti-Glare |
| Color arrangement | RGB-stripe |
| Interface | RGB |
| View direction(Gray Inversion) | 6 O’Clock |
| Backlight power consumption | 2.046W(Typ.) |
| Panel power consumption | 0.360W(Typ.) |
| Weight | TBD |
RGB 9 Inch TFT with RTP Product Drawing
Absolute Maximum Ratings
| Item | Symbol | Values | Unit | Remark |
| Min. | Max. |
| Power voltage | DVDD | -0.3 | 5.0 | V | |
| AVDD | -0.5 | 13.5 | V | |
| VGH | 13.0 | 19.0 | V | |
| VGL | -12.0 | -2.0 | V | |
| VGH-VGL | - | 31.0 | V | |
| Operation Temperature Storage Temperature | TOP | -20 | 70 | ℃ | |
| TST | -30 | 80 | ℃ | |
| LED Reverse Voltage | VR | - | 1.2 | V | Each LED Note 2 |
| LED Forward Current | IF | - | 25 | mA | Each LED |
Typical Operation Conditions
(GND=AVSS=0V, Note 1)
| Item | Symbol | Values | Unit | Remark |
| Min. | Typ. | Max. |
| Power voltage | DVDD | 3.0 | 3.3 | 3.6 | V | Note 2 |
| AVDD | 10.2 | 10.4 | 10.6 | V | |
| VGH | 16.3 | 17.0 | 17.7 | V | |
| VGL | -5.7 | -5.0 | -4.3 | V | |
| Input signal voltage | VCOM | 3.2 | 4.2 | 5.2 | V | Note 4 |
| Input logic high voltage | VIH | 0.7 DVDD | - | DVDD | V | Note 3 |
| Input logic low voltage | VIL | 0 | - | 0.3 DVDD | V |
Note 1: Be sure to apply DVDD and VGL to the LCD first, and then apply VGH.
Note 2: DVDD setting should match the signals output voltage (refer to Note 3) of customer’s system board.
Note 3: DCLK,HS,VS,RESET,U/D, L/R,DE,R0~R7,G0~G7,B0~B7,MODE,DITHB.
Note 4: Typical VCOM is only a reference value, it must be optimized according to each LCM. Be sure to use VR.
Current Consumption
(GND=AVSS=0V)
| Item | Symbol | Values | Unit | Remark |
| Min. | Typ. | Max. |
| Current for Driver | IGH | - | 0.3 | 1 | mA | VGH =17.0V |
| IGL | - | 0.3 | 1 | mA | VGL = -5.0V |
| IDVDD | - | 5.5 | 10 | mA | VCC =3.3V |
| IAVDD | - | 32 | 50 | mA | AVDD =10.4V |
Backlight Driving Conditions
|
Item
| Symbol | Values | Unit | Remark |
| Min. | Typ. | Max. |
| Voltage for LED backlight | VL | 8.4 | 9.3 | 10.2 | V | Note 1 |
| Current for LED backlight | IL | 198 | 220 | 242 | mA | |
| LED life time | - | 40,000 | - | - | Hr | Note 2 |
Note 1: The LED Supply Voltage is defined by the number of LED at Ta=25℃ and IL =220mA.
Note 2: The “LED life time” is defined as the module brightness decrease to 50% original brightness at Ta=25℃ and IL =220mA. The LED lifetime could be decreased if
operating IL is lager than 220 mA.
Pin Definition
| No. | Symbol | I / O | Function |
| 1 | VLED | - | Power for LED backlight |
| 2 | VLED | - | Power for LED backlight |
| 3 | GLED | - | Ground for LED backlight |
| 4 | GLED | - | Ground for LED backlight |
| 5 | GND | P | Power ground |
| 6 | VCOM | I | Common voltage |
| 7 | DVDD | P | Power for Digital Circuit |
| 8 | MODE | I | DE/SYNC mode select |
| 9 | DE | I | Data Input Enable |
| 10 | VS | I | Vertical Sync Input |
| 11 | HS | I | Horizontal Sync Input |
| 12 - 19 | B7 - B0 | I | Blue data(MSB) |
| 20 - 27 | G7 - G0 | I | Green data(MSB) |
| 28 - 35 | R7 | I | Red data(MSB) |
| 36 | GND | P | Power Ground |
| 37 | DCLK | I | Sample clock |
| 38 | GND | P | Power Ground |
| 39 | L/R | I | Left / right selection |
| 40 | U/D | I | Up/down selection |
| 41 | VGH | P | Gate ON Voltage |
| 42 | VGL | P | Gate OFF Voltage |
| 43 | AVDD | P | Power for Analog Circuit |
| 44 | RESET | I | Global reset pin. |
| 45 | NC | - | No connection |
| 46 | VCOM | I | Common Voltage |
| 47 | DITHB | I | Dithering function |
| 48 | GND | P | Power Ground |
| 49 | NC | - | No connection |
| 50 | NC | - | No connection |
RGB 9 Inch TFT with RTP Product Image
Factory Facilities and Certificates
Contact Us
We love to hear about your projects, If you have any questions, we can be reached at sales2@saef.com.cn
Product Tags:
|
|
RGB Interface 9 Inch TFT LCD 800*480 Dots With Resistive Touch Screen Images
|
